Good investment

Positive results in shredding railway sleepers

In the waste wood processing industry, railway sleepers are among the most difficult materials to shred. They are made of very hard wood and often still contain iron screws and plates. When Gojer, Kärntner Entsorgungsdienst GmbH was faced with the challenge of shredding these sleepers, they opted for the Urraco 95 DK mobile twin-shaft shredder from Lindner-Recyclingtech at the end of August 2017 and looks back on a very positive first year.

Albert Einstein is claimed to have once remarked: “Wood chopping is so popular because you can immediately see the results.” At Gojer, Kärntner Entsorgungsdienst GmbH in Völkermarkt/Austria, however, wood is not simply chopped: railway sleepers and other waste wood are shredded in large quantities. For over a year, the Urraco 95 DK mobile shredder has been helping the firm tackle the task.

 

Over 10 000 metric tonnes of railway sleepers shredded

The tracked Lindner mobile twin shaft shredder, featuring two speeds and an intuitive radio remote control, has already processed more than 24 000 metric tonnes of waste wood, including more than 10 000 metric tonnes of decommissioned railway sleepers. Gojer‘s input material is acquired from Austria as well as neighbouring European countries. After shredding, the material is transported to an incineration plant in Austria, which is the country‘s only facility fitted with a special filtering system for the incineration of treated railway sleepers. The Urraco 95 DK is designed for high throughput rates and is capable of generating a higher output, i.e. more of the facility’s capacity could be utilised should more waste become available on the market, notes Oskar Preinig, Managing Director of Gojer, Kärntner Entsorgungsdienst GmbH. He also added that “depending on the requirements and the material, the machine can shred 140 metric tonnes of waste wood per hour.”

 

900 operating hours clocked before first shaft replacement

Oskar Preinig knows of no other shredder as powerful as the 770 HP Urraco 95 DK, especially for processing railway sleepers. “Railway sleepers are made of very hard wood,” says Preinig when asked about the challenges facing the shredder. “This wood does not break as easily as other types and is therefore much more difficult to shred than conventional waste wood. The Urraco 95 DK accomplishes the task with flying colours and is extremely resistant to unshreddables.” Railway sleepers often contain iron plates, screws and nails. In the facility in Carinthia, these elements are separated from the material flow post-shredding by downstream overbelt magnets. “The metal parts in the input material represent an additional challenge for any shredder,” admits Oskar Preinig. “But they don‘t faze the Urraco 95 DK. It is always impressive to see how the shredder processes these iron parts without suffering any damage.” 

Gojer was particularly impressed by the fact that during its first year of operation, the Urraco 95 DK only required its first shaft change after 900 operating hours. “That’s a long time considering the amounts we process,” says Preinig. “The machine is also very cost-effective if you weigh up performance and fuel consumption.” To achieve maximum engine output, the machine‘s powerful hydraulic system is equipped with a Lindner two-tower planetary gearbox. That is why the compact and robust Urraco 95 DK is able to effortlessly achieve the required output size of 150 mm. 

This was also confirmed by operations manager Florian Kordesch, who once again reiterated the stability of the shaft system, which features a shaft length of 2 x 2500 mm and fourfold crushing and cutting action per shaft rotation. The automatic and load-dependent reverse mode is also an indicator of the machine’s cost efficiency and commanding performance when it comes to unshreddables.

 

Efficient from start to finish

According to machine operator Stefan Pinter, machine failures due to unshreddables can be ruled out. The tearing hooks always pull in the sleepers uniformly and very efficiently. Furthermore, the Urraco 95 DK is hardwearing, maintenance-friendly and, according to Pinter, easy to operate. “It’s possible to operate the machine entirely from the wheel loader, which is used to feed the shredder. Only one person is needed to operate and feed the machine,” says Pinter. “The joystick remote control and the touch display on the machine itself are really convenient and extremely easy and intuitive to use.”

 

www.gojer.at

www.l-rt.com

Related articles:

Issue 2019-04

Lindner’s mobile shredders and system solutions

A multitude of different configuration options make Lindner’s mobile shredders and system solutions the perfect choice for universal waste processing. The company will be demonstrating just what is...

more
Issue 2019-04

Live in Action – The VZ 950 TITAN at the RecyclingAKTIV show

Since the market launch of the VZ 950 TITAN over a year ago, ARJES has not come to a halt. Over the past few months the powerful shredder has been continuously developed and optimised in order to...

more
Issue 2018-01 Two new products

Strong trade-show appearance from HAMMEL Recyclingtechnik GmbH

This year’s trade-show unveiled two new product innovations, the first being the primary shredder 750 DK extra power and the secondary shredder HEM 400 D. The HAMMEL primary shredder type 750 DK...

more
Issue 2018-05

THM recycling solutions GmbH presents new products

THM recycling solution GmbH presents two new machine types as well as extensions of size variants for existing machine types. Granulator Type ZMK1607 and ZMK2007 This new machine type is a new...

more
Issue 2018-05

ANDRITZ to supply a Universal Shredder FRP to Sweden

International technology Group ANDRITZ has received an order from AB Hilmer Andersson, a family-run company operating in the wood processing industry, to supply a Universal Shredder FRP to their saw...

more